Power Roll Turner Gin Stand
Conversions

The Slover Power Roll Turner Gin Stand unlocks the gin stand and
the amount of HP you put on the saw shaft is the limiting factor of its
capacity. Our Power Roll Turner will out gin any other brand gin
stand.

With a Slover Power Roll Turner Gin Stand you can lose half of the
saw teeth off of every saw in the gin stand and it will still gin about
the same amount of cotton.

The roll turner helps to drive the seed roll straight around which
keeps the white streaks in the seed roll lined up directly over the gin
saws. This puts the saw HP directly into the seed roll for added
traction and higher capacity.

We put a new roll box front in the gin stand with a slot all the way
across the gin stand. This slot skims ginned seed out of the seed roll
so all of the seed do not have to discharge out the bottom of the
seed roll. This gives the gin stand higher capacity.

When a standard gin stand begins to lose cotton on one end or the
other the seed roll locks down and the ginner has to pull the gin
stand out of the ginning position and dig around in the seed roll to
loosen it up and the start it to ginning again. So you lose capacity.

With the seed skimmer the gin stand just keeps on ginning when
there is no cotton on one end and the seed roll does not lock down
and stop ginning. So there is no capacity loss.

We also put a rotating huller rib in the gin stand which is located in
the front of the gin stand above the picker roller. The rotating huller
rib has a series of disks on it. The disks stick in between each gin
saw and the cotton the gin saw pick up in the front of the gin saw is
pulled by the saw between each disk.

This action assures that the cotton is directly over each gin saw
when it gets into the seed roll and that the cotton does not overlap
between the saws because the disk separate the cotton and this
insures that the seed discharge between each gin saw is not covered
up by the incoming cotton.  

Keeping the seed discharge path open so that the seed do not have
to fight their way through the incoming cotton allows the seed to
discharge easily increases the capacity of the gin stand.

We furnish a new picker roller that we call a smooth picker roller. The
surface of this picker roller does not have spikes or other protrusions
as your picker roller does. With out smooth picker roller very few
seed locks of cotton get by and into your seed, which makes your
seed pile look white because your gin stand did not gin the cotton off
of these seed.

We furnish a new roll box top that has a single latch for ease of
opening.

Some gin stands the doffing brush does not properly doff the gin saw
which reduces the gin stand capacity. We furnish new scrolls to make
the brush doff the gin saw properly and also vacuum out the gin
stand as it should.

We also have steel doffing cylinders to replace your hair brush
doffer. A rib fire or overhead fire does not burn the flights off these
doffers. The steel flighted doffer never gets out of balance. The steel
flighted doffer does not give up when ginning wet cotton as your hair
brush doffers do.

Some gin stand do not have a very good breast lift. We furnish a new
breast lift when needed that has a 2 3/16" shaft across the gin stand
with arms that attach to each end of the gin breast. This always
keeps the gin breast square with the gin saw and does not allow on
end of the gin breast to lag behind and the ribs hit the gin saw teeth
which damages the gin saw on that end.

We put a 4" bore air cylinder on the gin stand to operate the 2 3/16"
shaft. This insures plenty of power to move the gin breast in and out
and 2 or 3 men do not have to run over hand help the gin breast in
or out every time as they do now.

You can walk up to a Slover Power Roll Turner Gin Stand that is
ginning at full capacity and stretch your arms out and block the
cotton coming down the feeder apron until it almost chokes the
feeder and then turn it loose and the gin stand will just swallow the
cotton.

You can do that over and over in rapid succession and the gin stand
just swallows the cotton time after time.

WE HAVE PUT OUR POWER ROLL TURNER CONVERSION KITS IN
ALL MAKES OF GIN STANDS. WHEN THE FULL CONVERSION KIT
IS INSTALLED IT UNLOCKS THE GIN STAND TO HIGHER CAPACITY
AND CAPACITY IS LIMITED ONLY BY THE AMOUNT OF HP YOU
CAN APPLY TO THE SAW SHAFT.

THE SLOVER POWER ROLL TURNER GIN STAND CONVERSION
KIT MAKES A GIN STAND A 15 BALE PER HOUR OR MORE GIN
STAND FROM WHAT YOU HAVE.

ALL SLOVER POWER ROLL TURNER GIN STAND CONVERSIONS
DRIVE FROM THE SAW SHAFT AND THERE IS NO ELECTRIC
MOTOR OR GEAR BOX TO GIVE TROUBLE.

Prices for Murray, Continental, Hard-Wicketter complete conversions
starting at $22,500.00.